Prach

SCPI Commands :

TRIGger:LTE:MEASurement<Instance>:PRACh:THReshold
TRIGger:LTE:MEASurement<Instance>:PRACh:SLOPe
TRIGger:LTE:MEASurement<Instance>:PRACh:TOUT
TRIGger:LTE:MEASurement<Instance>:PRACh:MGAP

class PrachCls

Prach commands group definition. 4 total commands, 0 Subgroups, 4 group commands

get_mgap() → float

# SCPI: TRIGger:LTE:MEASurement<Instance>:PRACh:MGAP
value: float = driver.trigger.lteMeas.prach.get_mgap()

Sets a minimum time during which the IF signal must be below the trigger threshold before the trigger is armed so that an IF power trigger event can be generated.

return:

min_trig_gap: No help available

get_slope() → SignalSlope

# SCPI: TRIGger:LTE:MEASurement<Instance>:PRACh:SLOPe
value: enums.SignalSlope = driver.trigger.lteMeas.prach.get_slope()

Qualifies whether the trigger event is generated at the rising or at the falling edge of the trigger pulse (valid for external and power trigger sources) .

return:

slope: REDGe: Rising edge FEDGe: Falling edge

get_threshold() → float

# SCPI: TRIGger:LTE:MEASurement<Instance>:PRACh:THReshold
value: float or bool = driver.trigger.lteMeas.prach.get_threshold()

Defines the trigger threshold for power trigger sources.

return:

trig_threshold: (float or boolean) No help available

get_timeout() → float

# SCPI: TRIGger:LTE:MEASurement<Instance>:PRACh:TOUT
value: float or bool = driver.trigger.lteMeas.prach.get_timeout()

Selects the maximum time that the measurement waits for a trigger event before it stops in remote control mode or indicates a trigger timeout in manual operation mode. This setting has no influence on Free Run measurements.

return:

trigger_timeout: (float or boolean) No help available

set_mgap(min_trig_gap: float) → None

# SCPI: TRIGger:LTE:MEASurement<Instance>:PRACh:MGAP
driver.trigger.lteMeas.prach.set_mgap(min_trig_gap = 1.0)

Sets a minimum time during which the IF signal must be below the trigger threshold before the trigger is armed so that an IF power trigger event can be generated.

param min_trig_gap:

No help available

set_slope(slope: SignalSlope) → None

# SCPI: TRIGger:LTE:MEASurement<Instance>:PRACh:SLOPe
driver.trigger.lteMeas.prach.set_slope(slope = enums.SignalSlope.FEDGe)

Qualifies whether the trigger event is generated at the rising or at the falling edge of the trigger pulse (valid for external and power trigger sources) .

param slope:

REDGe: Rising edge FEDGe: Falling edge

set_threshold(trig_threshold: float) → None

# SCPI: TRIGger:LTE:MEASurement<Instance>:PRACh:THReshold
driver.trigger.lteMeas.prach.set_threshold(trig_threshold = 1.0)

Defines the trigger threshold for power trigger sources.

param trig_threshold:

(float or boolean) No help available

set_timeout(trigger_timeout: float) → None

# SCPI: TRIGger:LTE:MEASurement<Instance>:PRACh:TOUT
driver.trigger.lteMeas.prach.set_timeout(trigger_timeout = 1.0)

Selects the maximum time that the measurement waits for a trigger event before it stops in remote control mode or indicates a trigger timeout in manual operation mode. This setting has no influence on Free Run measurements.

param trigger_timeout:

(float or boolean) No help available